- Eliminates white heat rings and water marks
- Blends out scratches and blemishes
- Restores colour and lustre to faded finishes
- Will NOT dissolve existing finish
How does it work?
Restor-A-Finish is a unique finish-penetrating formula that restores the original colour and lustre to your finish while blending out the blemishes and minor scratches. Restor-A-Finish cleans the surface and restores the finish in one step - without removing any of the existing finish.
Restore It - Don't Strip It!
With a simple wipe-on, wipe-off process, most finished wood surfaces that seem to need a refinishing job can be completely restored in a few minutes. White heat rings and water marks, sun fade, oxidation, smoke damage, and most other blemishes can be quickly eliminated. Before you go to the extreme of stripping it, try restoring it!
Treat Scratches, Nicks, and Abrasions
Restor-A-Finish works best when applied with a small pad of towelling, or for severe white rings and crazing, with Super Fine (0000) steel wool. DO NOT pour directly on the finish. When using steel wool, always rub with the grain of the wood. First, determine the pressure you should use on an inconspicuous spot, as the hardness of finishes vary.
White Heat Rings and Water and Smoke Damage
Apply Restor-A-Finish (see above) with steel wool and rub hard enough with the grain of the wood to blend out the white effect. If high gloss finish should appear dull due to the use of steel wool, polish it out with Howard Restor-A-Shine polishing compound.
Revive Wood Finishes
Wipe on the appropriate colour of Restor-A-Finish with a clean cloth. Let it stand for a few minutes then wipe dry. If you desire a darker shade, simply apply a darker colour of Restor-A-Finish.
Raised and Blistered Finishes
Apply Neutral Restor-A-Finish (to prevent darkening of wood beyond temporary "wet effect") with steel wool. As blisters soften press down while the Restor-A-Finish is applied. Wipe dry, and again later if the surface "blooms" with excess Restor-A-Finish.
Restore Minor Crazed or Checked Finishes
Apply Restor-A-Finish with Medium Grade (00) steel wool. Rub hard enough to smooth out the finish, periodically checking your progress. Checked or crazed surfaces may absorb an excess of Restor-A-Finish and "bloom out" requiring another wiping later.
Treat Carved Wood
Restor-A-Finish has saved many hours of labour by chemically cleaning and restoring the finish on carved portions of furniture and clocks. Simply apply Restor-A-Finish with a small paint brush or soft tooth brush and wipe off.
Be careful to protect fabric, carpets, and linoleum when applying Restor-A-Finish. It may leave a permanent stain. If spilling occurs, immediately scrub areas with straight liquid detergent or stain remover and wipe dry. Be sure to cover a small area at a time when applying Restor-A-Finish. Always wipe dry. DO NOT apply Restor-A-Finish to the new imitation wood finishes or use it under polyurethane finishes as a stain!
- Kitchen drawers peelingReview by Sandy
Hello, I just noticed that the front of my cupboards in front of the kitchen sink, needed to have something done. I am wondering which of your products I should use?
Thanks for your reply.
It looks really great now. I just applied the Restor-A-Finish with a cloth in most places, but on another spot that was more damaged and the 'finish' seemed to have been peeled away, I used the steel wool, dampened with the restor-a-finish. The colour is perfect and the cabinets that I emailed to you look wonderful, just using the restor-a-finish. Many thanks, Sandy
(Posted on 18/01/2016)
- Just BriliantReview by Bernie60
- My reproduction mahogany table, which I have had for over 30 years, survived the trip to Aus but not my son putting a wet bowl of water on it. Leaving a large white ring on the edge. I though removing the stain would be a drama but I was pleasantly surprised at how easily & effectively it was, the mark disappeared in one application. I am now refreshing the rest of my furniture. (Posted on 7/01/2016)